Go to content
Leren riem met gaatjes naast een automatische riem zonder gaatjes op een eiken tafel

Ratchet belt: how a belt without holes works, and whether it suits you

A ratchet belt adjusts in half-centimetre steps instead of holes. How a belt without holes works, plus the honest pros and cons compared with a classic belt.

You are standing there in the morning, belt in hand, and one hole is just too tight while the next is just too loose. After lunch you would happily let it out a little. A belt without holes promises to fix exactly that, and to a large extent it does.

The short answer: a ratchet belt (also sold as an automatic belt or a belt without holes) has a track of small teeth along the back. The buckle clicks into that track in steps of roughly 5 to 6 mm, instead of the 2.5 cm or so between two holes. That gives a more precise fit. The trade-off is that you depend on a small mechanism, the buckle is bigger, and on most models you cannot fit a different buckle. If you sit a lot or your waist changes during the day, a ratchet belt can be a genuine relief. If you want one belt to wear for twenty years, a classic belt with holes is often the better choice.

How does a ratchet belt work?

Turn a ratchet belt over and you see it straight away: running along the inside is a strip with fine ridges, usually plastic, sometimes pressed into the leather itself. Inside the buckle sits a small pawl on a spring. As you pull the belt through, the pawl slides over the ridges and drops into the next notch. It will not slide back unless you press the lever or button on the buckle. Then the pawl lifts and the belt lets out.

It is the same idea as a cable tie or a ski boot. Tightening happens almost by itself, releasing takes a deliberate move. Most brands leave the front of the leather completely unpunched, which is why these belts look so clean.

You set the length once. The belt usually arrives too long, you cut it to size and fix the end into the buckle with a clamp or small screw. Measure carefully before you cut, because a belt cut too short will never get longer.

Other belts without holes

The ratchet belt is the best known option, but not the only way to go without holes. The table puts them side by side, with a standard holed belt for comparison.

TypeHow it holdsAdjustmentWeak point
Ratchet belt (automatic)Pawl in the buckle clicks into a toothed trackSteps of approx. 5 to 6 mmWear on the track or spring, large buckle
Clamp or friction buckleA hinged bar grips the leatherSteplessCan slip, leaves pressure marks in the leather
Braided beltThe prong goes between the strandsAlmost steplessBraid stretches over time, looks less formal
Classic belt with holesProng through a punched holeSteps of approx. 2.5 cmStretched holes, your size can fall between two holes

The advantages of a belt without holes

The big plus is fine adjustment. Two holes are about 2.5 cm apart, which is simply too coarse for a lot of people. With half-centimetre steps you always find a setting that fits. After a meal, on a long drive or after hours at a desk, you let it out one notch without anyone noticing.

There are also no holes to wear out. On a classic belt you can tell after a few years which hole is the favourite: it has pulled oval and the leather around it bulges. A ratchet belt spreads the load along the track, so that does not happen.

And you can work it with one hand. For people with stiff fingers or weak grip, that is not a small thing.

The drawbacks, honestly

A belt with a mechanism has a weak point, and it is the mechanism. The spring in the buckle and the teeth on the track work every single day. On cheap models the track is thin plastic and the belt starts slipping after a year or two. That cannot be repaired; you buy a new one.

Then there is the leather. Because a track is glued or stitched to the back, many makers use thinner leather, often coated split leather or a laminate of several layers. That is not automatically bad, but it behaves differently from a belt cut from one thick strip of full-grain leather. It moulds less to your body and barely develops a patina.

The buckle is larger and flatter, since the mechanism has to live somewhere. With jeans you will not notice. With a suit, a chunky plate buckle can look a little technical. On most brands you can only replace the buckle with one from the same maker, if it is still available.

One more practical point that often gets overlooked: you cut the belt to size. If you later lose or gain a fair bit of weight, you have less room to play with than on a belt with five holes.

Who is a ratchet belt a good choice for?

A belt without holes suits people whose waist changes through the day or over the months, people who sit a lot and like to loosen their belt now and then, and anyone who struggles to find the right hole. It is handy when travelling too: you get it off and on faster at security, although like any belt with a metal buckle it still has to come off for the scanner.

It is less suitable if you want one belt that lasts for decades. A thick belt in vegetable-tanned leather with a simple buckle can last a lifetime because there is nothing in it to break. If the buckle fails, you fit a new one. If the holes stretch a little, that becomes part of its character. That is also why the Beocca Oden men's leather belt simply has holes and a brass buckle: less fine-tuning, but nothing that can jam.

If you are torn between the two, the article on choosing a leather belt that lasts for years covers the rest of the decision, such as width and leather type.

Always between two holes? There is another fix

Often the wish for a belt without holes comes down to one problem: your favourite belt sits just wrong. You can solve that without buying a new belt. An extra hole exactly halfway between two existing ones gives you the missing centimetre, as long as you use a proper hole punch and not a screwdriver. How to do that without tearing the leather is explained in making an extra hole in a leather belt.

Another tip that makes a real difference: do not base your belt size on your trouser size, but on a belt that fits you now. Measure from the fold at the buckle to the hole you use. If that hole sits in the middle of the row, you have room either way and are less likely to land between two settings.

Whatever belt you choose, with or without holes: leather that dries out cracks sooner, especially where it bends. A little leather balm twice a year keeps a belt supple, as described in how to care for a leather belt. On a ratchet belt, keep the balm off the track. It does not belong there, and it makes the teeth slippery.

Search

Back to top

Shopping cart

Your shopping cart is currently empty

Shop now